Wednesday, February 29, 2012

Room for Three???

Pin It

As many of my readers know C and I are the parents of 2 wonderful kids. Goo is 4 and Gouda is 1. I thought we were done. I wanted to be done. I asked C if he was ready to get a vasectomy. The course we agreed on for when we were done having children. C replied that no he was not going to have a vasectomy because he was not done having kids. He said that we needed one more child. We have spent the last two months arguing this point. I wanted to concentrate on the 2 kids we have and my new career as a Doula. I am pending certification right now and have 2 clients.

Finally C suggested that we both pray about it. I was confident that I'd get the answer that our family was complete so I agreed. There is an old Jewish saying "If you want to make God laugh tell him your plans". I got the wrong answer!

We are not done having kids. There will be one more!

C and I have fertility problems so getting pregnant isn't as easy as saying "OK let's have another one". C has began taking his COq-10 to improve his sperm motility and I am taking prenatal. In 4 months or so we will if the pills work a 2nd time for us....

I'd love to say more here but I promised little Goo I'd build a fort with him and that's more important than a blog.

Monday, February 27, 2012

I found them Bengal BBQ Recipes!

Pin It

I love Disneyland. I got engaged in front of Snow White's Wishing Well. C and I had our Honeymoon there and we have a family tradition of introducing our babies to the Happiest Place on earth when they are 4 months old. I love the Bengal BBQ. It is a little snack shop accross from Tarzan's Tree House. I haven't been in awhile but it's good to know that now I can have a taste of Disneyland anytime I want....

Korean Sauce (Beef Dip)

Bengal Barbecue


1 c. Soy Sauce
1½ c. Water
1 T. Ground Black Pepper
3 T. Sesame Seed Oil
1 t. Ground Red Pepper
½ t. Cayenne Pepper
1 T. Fresh Garlic
1 T. Corn Starch


Mix all ingredients except corn starch.
Bring to a slow boil over medium heat.
Add corn starch to thicken.

[To top]

Safari Skewers

Bengal Barbecue


1 pound fresh asparagus (thick stalks)
1 pound bacon (regular cut)
1 lemon


Cut asparagus and bacon into thirds. Wrap bacon around asparagus pieces, and skewer (place the pieces on horizontally and not lengthwise - be sure to pierce the end of the bacon to prevent it from unraveling).

Place on outdoor grill, turning frequently. Squeeze some lemon juice over the skewers while grilling.

Skewers are done when bacon is thoroughly cooked, and slightly charred around the edges.

Squeeze some extra lemon upon removing from the grill.

[To top]

Spicy Beef Skewers

Bengal Barbecue


1 c. Soy Sauce
1 1/2 c. Water
1 T. Ground Black Pepper
3 T. Sesame Seed Oil
1 t. Ground Red Pepper
1/2 t. Cayenne Pepper
1 T. Granulated Garlic
3 T. Cornstarch
18 1-oz. pieces Sirloin Beef Chunks
6 Bamboo Skewers


Combine all of the ingredients above and bring to a boil, adding cornstarch to thicken. Soak the bamboo skewers in water to avoid burning. Place 3 pieces of beef on each skewer and cook on the grill 3 minutes on each side or until desired doneness. Brush with sauce and serve.

Yield: 2 3/4 cups sauce
Servings: 6

[To top]

Tahitian Sauce (Chicken Dip)

Bengal Barbecue


4 Whole Cloves
1 T. Red Wine Vinegar
1 c. Ketchup
½ c. Crushed Pineapple
½ c. Pineapple Juice
½ c. Brown Sugar
½ c. Soy Sauce
¼ c. Orange Juice Concentrate
3 T. Water


Simmer cloves in vinegar for 5-10 minutes. Strain cloves and add other ingredients.
Bring mixture to slow boil over medium heat.

[To top]

Tonkatsu Sauce (Chicken Marinade)

Bengal Barbecue


1 c. Teriyaki Sauce
1 c. Soy Sauce
1 T. Red Wine Vinegar
1 c. Brown Sugar
½ c. Sherry Cooking Wine
2 Whole Bay Leaves
1 T. Ground Black Pepper
3 T. Grated Fresh Ginger Root
2 T. Fresh Garlic, finely minced


Mix ingredients and marinate chicken overnight in your refrigerator.

[To top]

Friday, February 24, 2012

Dishwasher Vinyl

Pin It
Maybe this is only a problem in my house, but I never know if the the dishes in the dishwasher are clean or dirty.  Quite a few times I've grabbed something out of it thinking it was clean only to find some sort of gunk stuck to it. Yuck!  On the other side I've ran the dishwasher only to find out that my hubby ran it already.  What a waste of water and soap!  So I devised a little solution.

Now all we have to do is move the magnet to clean when we run it and dirty when we unload it. Pretty simple. :)
Here's how I did it.

First, cut out the design, then weed out all the vinyl that is not part of the design.

Next, put mashing tape over the design.  I use masking tape instead of transfer paper because it is a lot cheaper, but you get the same result.

Peel off the paper backing

Place it where you want it.

Use a putty knife or other flat surface to firmly press on the vinyl.  This ensures that it will stick. 

Remove the tape.

Stand back and admire your work!

See you next week,

Thursday, February 23, 2012

Meat on a Stick

Pin It

Or if you are Jose Jalepeno on a steek! I have learned a secret to get my kids to eat something other than hot dogs or chicken nuggets. You must put it on a stick and then grill it.... They will eat the meat like it was a directive straight from Heaven. (i thought that was a good analogy for Lent). Wait is it Lent yet?
So here is my tutorial about meat on a stick. These things asle for a $1.00 a stick in the meat counter of my local supermarket but I made these for about 50 cents a piece plus I can marinate them the way I want and not the way the Butcher thinks it should be.

Use Chicken Tenders

Be sure to soak your sticks for a half hour before placing on grill

All ready for the grill

Add any sauce or marinade you want

throw them on the BBQ grill

All Done
Now sit back and watch the kids devore the meat on a stick! PS... young children should not be given sharp sticks!

Now my new quest is to find the recipe for the Bengal BBQ in Disneyland and make those!

Wednesday, February 22, 2012

New Chandiler in the Hall

Pin It

I picked up this little gem from IKEA for $39.99.

Close up Mr. DeMille

Tuesday, February 21, 2012

Item Found!

Pin It

We have no dining room table. Right now we don't even have a place to put one but that's all about to change. My neighbor gave us this little beauty and with some major modifications I'll transform it to be a table for us. It is Faux Marble and has a huge burn mark but I can fix that!

Monday, February 20, 2012

Pin It

Lovely Crafty Home

I ran accross this the other day and thought OH my Heck I have all the stuff to do this right now in my craft/decor supplies and I even have a place I'd like to try it out. THE STAIRS in the Villa Tranquilla...

Maybe mom wouldn't notice?

My brown paper floors are by far my most viewed content, at the top of the list for FAQs, and seen more on Pinterest than anything else I’ve done. I think that’s kinda cool for such an easy and cheap floor solution! But I cannot take credit for this method alone, I originally saw this idea in a magazine that featured Jami from An Oregon Cottage. I changed a few things about the process to suit my tastes, but her site is also a great resource.
I wanted to put all the details in one place (instead of scattered over several posts) to make it easier for you to start your project. Keep in mind this is the method I have done in my house over plywood subfloors. There are other methods out there, but I can only tell you what has worked for me. If you have cement/concrete subfloor, these instructions as written will not work. Please click here for advice from others.
Ok let’s get started! Want to rid your house of bad carpet/linoleum/vinyl/etc?! Here’s what you’ll need for a large room:
  • Brown craft paper on a roll-$11
  • Elmer’s Glue (by the gallon, check A.C. Moore/Michaels/other craft stores)- use a 40% off coupon, it will run about $12
  • Small bucket
  • Paint brush
  • Roller tray
  • Stain (optional, I used Minwax Dark Walnut)- $8
  • Floor Grade Polyurethane (I used this in semi-gloss)- $40
  • Sponge pad on wood block mop head to apply poly- $5
  • Lambskin stain pad refill (if you’re using stain- this fits on the same wood block as above)- $6
  • Extension pole (universal screw in connection for the mop blocks or paint rollers)-$9
  • 3″ chip brush- $1.50
  • Gloves
The start up materials cost about $100, but will likely last for a few rooms (or into other projects, it’s always handy to have an extension pole). I did about 650 sq ft in my home for around $200.
First things first, prepare your floor. In my case, that involved removing the carpet, pad, and staples. I also sanded down any high spots (our subfloor had areas with plaster/glue or something on them), filled any deep nail holes, hammered in any loose nails, and filled any gaps between boards. Keep in mind when using filler that you usually want to overfill a bit because even though the package says it won’t shrink-it does. When it’s set, sand the filler down flush with the floor.
I’ll be the first to tell you that I absolutely hate prep work-especially sanding. But trust me, don’t skip this. Go ahead and tape off your baseboards if you really don’t want to do any touch up work. Once your floor is filled, sanded, and vacuumed (or swept), you’re ready for the paper.
It is probably faster to tear a bunch of paper, wad it up into garbage bags, then start. But I pretty much tear as I go, somehow seeing the progress helps and also allows me to take a break from sitting on the floor with glue hands. Get out your roll of paper and start tearing-keeping the pieces with straight edges separate from the ones torn from the middle of the roll. I like my pieces to be anywhere from 6″-12″ in diameter, but it really depends on the look you want. The smaller the pieces, the more wrinkly/leathery/vein-y the final result will be. As you tear, crumple the pieces into balls and toss into a bag or pile.
Next, mix up your glue. I don’t like to mix a lot at a time because you may need to stop or take a break, and you won’t want the glue to dry up and go to waste. I typically mix up 2-3 “batches” using a 3:1 ratio of water:glue- so 6-9 cups of water to 2-3 cups of glue at a time. This will fit it a 2 gallon bucket easily. Stir it up with a paint stick or a gloved hand.
Now you’re ready to start! Using a paint brush, brush the area you’re working in with the glue mixture then dunk 5-6 balls of paper in your glue mix. I have found this is the perfect amount of paper and working time for one person. As soon as you dunk the paper, you want to start submerging it and squeezing it out. I pull each ball out and set it on the floor until it’s time to use it. This is important: do NOT leave the paper in the glue too long. You will only have to leave it in too long once to realize how long that is. It will tear and break down and generally be a pain to use. So just dunk, squeeze, and set aside. Repeat if necessary.
The straight edge pieces are perfect for the back of a stair tread (shown above) and underneath baseboard. I like to overlap the pieces by a few inches, obviously it will help with durability but it also looks more natural in my opinion. Don’t be afraid to brush glue mix on top of the pieces to help them lay flat and remove wrinkles.
You’ll want to paper yourself out of the room, or in the case of the hallway, leave hopping spots to be filled in later. For a staircase, work every other stair. Heat helps the glue dry, so if you feel like getting out a space heater you can (pictured in the bathroom above). I have found that no matter how large the room-with or without heat- it usually takes no longer than 12 hours (or, overnight) to dry.
Once the paper is dry, it’s time to stain (if you want). I prefer the look of the stain, but if you like the natural color feel free to skip down below to the polyurethane section. My whole upstairs is done with Minwax Dark Walnut. This is an oil based stain, so beware. I have never used a water based stain, but I have had someone comment that they tried it and didn’t get good results. If you want to use water based stain, test it on some scrap paper first before proceeding.
For a small area, you could get away with a lint free rag and chip brush. However, if you’re doing a room I highly recommend the extension pole/stain pad route. Here’s a neat tip to keep your roller trays in good shape: slide them into a small garbage bag and tape to secure. This is great for any oil based product, but helpful for latex paint too!
Using the chip brush, cut in around baseboards and trim. The stain pad makes staining a pretty quick process, so you can really cut in a fairly large area (like a whole wall or closet). When using the brush, dip it in the stain and then dab it in the top of the roller tray to remove excess. You really do not want to apply stain with a heavy hand. It is much better to need to dip your brush more often than to have a puddle of stain you need to disperse. It is for this reason that I absolutely DO NOT suggest the use of a foam brush. I have tried them and trust me-the chip brush is much easier to control and about the same price. When cutting in, be sure to “pull” the stain out a good bit from the wall, about 6″ or so. This will make it easier to blend the edges with the bulky mop pad.
Once you’ve cut in a large enough area, grab your extension pole and attach the lambswool pad to the wood block (if you’ve bought them separately, or bought one that came with the foam pad attached) by removing the wing nuts . The lambswool pad is meant for oil based products, so if you’re using water based stain this will not work (you’ll likely need two of the foam pads). Vacuum the lambswool pad for a minute to remove any loose fur or use a lint brush if your vacuum doesn’t have a hose. I cannot stress the importance of this step enough.
The extension pole screws into a threaded hole on the wood block. It may take a few tries to get it to go, as the block and pad end up being more angled then you might think. It’s not a 90 degree joint, so just look closely at the threads and try to line up the pole. Maybe that’s too much information, but I seriously almost threw the whole thing out the window the first time I tried this. I was convinced that “universal” was false advertising.
Once you’ve got your stain pad-on-a-stick assembled, pour some stain into your roller tray. Again, don’t over do it- you don’t want to splash it everywhere. Make sure you open any windows in the room before you start because you won’t be able to access them later. Dip the stain pad into the stain then blot it on the upper half of the tray by pushing gently downward to remove excess. Using long mop like movements, brush the stain on the floor in large sections. Blend it into the areas where you’ve cut in. If you’re new to this, it’s best to start in a closet. I have found that staining the paper is a lot different than staining wood. Since there is no grain, it really helps to use circular motions. Once you’ve laid down most of the stain from the pad (a few long straight mop strokes), you’ll have enough stain on the pad left to swirl around the edges and blend. While the stain is wet, you can move it pretty easily. Just don’t try to go back over it a few minutes later. Remember to mop yourself out. This is sometimes easier said than done, so just plan carefully.
This next part is probably the hardest. After doing several rooms/areas in all weather conditions, I have never found that the stain dries completely. What I mean by that is even after 24 hours, it will likely still be tacky. It took me a few tries to come up with the best method of applying the polyurethane given this annoying situation. You’ll be mopping first, then cutting in.
I used a water based poly because it is a quick dry and less smelly. Considering the amount of time spent applying it, I highly recommend going this route. It is more expensive, but please do not make your decision based on price (this is already such a cheap flooring solution). If you choose oil based poly, test it in an inconspicuous area first!
Using the extension pole again, attach the foam mop head to the wood block. Cover your roller tray with a garbage bag and pour in your poly of choice. Dip the mop head in the poly, blot out the excess, then apply it in long strokes on the floor. Stay away from the walls, you can cut this area in with a brush later. Be quick and wear socks. Just get that first coat down with minimal walking. It doesn’t have to be perfect. Once it dries, the tack will be gone and you can take your time cutting in around the baseboards and applying subsequent coats. Follow the directions for re-coating that your brand of poly suggests. I recommend no less than 12 coats.
I get asked a lot about sanding in between coats. The truth of the matter is that it does make a difference in how the floor feels under foot. It likely extends the life of the floor as well. However, who wants to sand an entire room? I didn’t. I sanded my stair treads and landing, and these areas are really smooth and lovely. But of course- these areas are also not covered with rugs and furniture. So to me it’s a trade off. If you want perfectly polished looking smooth floors, definitely sand with 220 grit-maybe not between each coat but definitely after the first and before the last.
To really finish the look, install quarter round or shoe molding. I’m in the process of starting this in my master bedroom, and it looks amazing.
1. How does the floor wear? Is it durable?
Well, it’s paper. So, considering that…it is remarkably durable. Once the poly is fully cured (sometimes up to a week), I find it is pretty resistant to scratches from normal traffic. I have a large dog and she can scratch the floor if she gets really crazy. It is similar to hardwoods in that way. I can’t guarantee it will last for 10 years, but I have heard that it can. It’s all in the application and general care of the floors. We have area rugs and felt feet on our furniture. I have never installed this in a bathroom or kitchen.
2. How long does it take?
I would say no matter how small the area, you’ll need at least 3 days without stain and 3 with stain.
3. What if my subfloor is not plywood?
I have no experience installing this on concrete/cement, tile, vinyl or linoleum. Some of my readers have suggested other methods which may work for your application. Please test in a small area to be sure.
And now here are some final shots from my house to get you motivated! Keep in mind all of these photos were taken on different days in different light, and you can see variation in how the floor photographs. But in person, it is very seamless and uniform.
{Basement Stairs-Natural, No Stain}
{Main Stairwell, March 2011}
{Main Stairwell, September 2011}
{Hallway And Ryan's Room}
{Ryan's Room}
{Hallway and Guest Room}
{Sneak Peak- Master Bedroom with Quarter Round Molding}

Concrete/Cement Tips
For concrete/cement subfloors, here are a list of things I have read or been told by others that do or do not work. Again, I have never done this so please test in a small area.
  • The 3:1 glue mix does not work for most.
  • A 50/50 glue mix has worked for some.
  • Using polyurethane only, brush it on the floor then lay the paper and brush more on top- do not saturate/dunk the paper.
  • If you have to use the poly only method, you cannot apply stain over the poly-it must be mixed in for the initial paper application. Look for “stain + polyurethane” products. I do not know anyone who has done this, so I have no idea how the stain+poly will affect the color of the paper.
  • I am curious to see if wallpaper glue would work

Wednesday, February 15, 2012


Pin It

In my last house I was a big fan of a place called Tatouage Designs. tatouage designs Link here. I spent A LOT of money on their designs and even though The Chateau is gone I still love the way it looked when I was done with it. Well, before things started collapsing on top of us. I thought just for a bit of nostalgia I'd post some of the pics here.

Master Bedroom
Added the Window and forgot to hang back the curtain

Railing for the Stairs

Guest Bedroom/ Game Room before kids

Dining Room

Tatouage goes on like a Rub on Transfer. It's easy to do and looks like you hired someone to paint Murals. 

Tuesday, February 14, 2012

Happy Valentine's Day

Pin It

                   Valentine's Table Display for $5.00 ( Dentist visit not included)